Research Article

Design and Performance Evaluation of a Battery-Assisted Fuel-Less Generator Using a Permanent Magnet Synchronous Generator with Automated Feedback Control

1 Bells University of Technology, Ota
2 Department of Mechanical Engineering, Bells University of Technology, Ota, Ogun State, Nigeria
* Corresponding author: ebomoniyi@bellsuniversity.edu.ng
Published: Jun, 2025
Pages: 112-121

Abstract

The energy insufficiency experienced in Nigeria is estimated to affect upwards of 85 million people, thus leading todependence on fuel-based generators. As such, environmental as well as socio-economic consequences are inevitable.This paper describes the process of designing, fabricating, and analyzing a closed-loop battery-assisted generator systemthat is fuel-free. The components used for the fabrication included a 12 V / 75 Ah battery bank, a 3 HP (2,237 W) DCmotor, and a three-phase PMSG of 10 kW. Also, a 6:1 belt and pulley speed ratio was employed to link the motor to thegenerator. The system was controlled using an auto-relay feedback loop which constantly monitored the voltage atterminals and redirected some of the generated current through a full bridge rectifier to recharge the battery. Thisarrangement extended the operational autonomy of the system without external intervention. Equations to determine theelectromagnetic flux linkage, mechanical power, pulley kinematics, system efficiency, and battery state-of-charge wereobtained and verified experimentally. Without any load, the prototype provided a constant voltage output of 220 V, 50Hz. During step load test from 35 W to 300 W, the maximum efficiency obtained was 74.88% at 100 W. When thefeedback loop was activated at 300 W, the system operated for 960 seconds compared to 360 seconds (2.67 times). Astatistical analysis of replicated experiments showed a mean efficiency of 74.88 ± 1.83 % at 100 W (95% CI: 70.26 to73.82%) using second order polynomial model.

References

  1. Adegoke, O. M., Ojo, A. O., Ohai, P. C., Gbadamosi, S. L., Lawan, R. O. , and Macaulay, A. J. 2022. Development of a 1kva Fuelless Generator Using a Brushed Direct Current Motor. ARPN Journal of Engineering and Applied Sciences, 17, 2089-2101.
  2. Aliemeke, B. N. G., Momoh, M. A., Asekhome, M. O., Anani, C. A. , and Vincent, A. C. 2024. Development of a 1.0 Kva Fuelless Generator. ABUAD Journal of Engineering Research and Development (AJERD), 7, 178-183.
  3. Ang, T.-Z., Salem, M., Kamarol, M., Das, H. S., Nazari, M. A. , and Prabaharan, N. 2022. A Comprehensive Study of Renewable Energy Sources: Classifications, Challenges and Suggestions. Energy strategy reviews, 43, 100939.
  4. Azeez, N., Ede, F. , and Oyelami, S. 2018. Design and Construction of a Fuelless Generator. EPRA International Journal of Multidisciplinary Research, 4, 29-35.
  5. Barré, O. , and Napame, B. 2016. Concentrated Windings in Compact Permanent Magnet Synchronous Generators: Managing Efficiency. Machines, 4, 2.
  6. Bhattacharya, M., Paramati, S. R., Ozturk, I. , and Bhattacharya, S. 2016. The Effect of Renewable Energy Consumption on Economic Growth: Evidence from Top 38 Countries. Applied energy, 162, 733-741.
  7. Daggash, H. A. , and Mac Dowell, N. 2021. Delivering Low-Carbon Electricity Systems in Sub-Saharan Africa: Insights from Nigeria. Energy & Environmental Science, 14, 4018-4037.
  8. Giwa, S. O., Nwaokocha, C. N. , and Samuel, D. O. 2023. Off-Grid Gasoline-Powered Generators: Pollutants' Footprints and Health Risk Assessment in Nigeria. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 45, 5352-5369.
  9. Hassan, Q., Algburi, S., Sameen, A. Z., Salman, H. M. , and Jaszczur, M. 2023. A Review of Hybrid Renewable Energy Systems: Solar and Wind-Powered Solutions: Challenges, Opportunities, and Policy Implications. Results in engineering, 20, 101621.
  10. Holechek, J. L., Geli, H. M., Sawalhah, M. N. , and Valdez, R. 2022. A Global Assessment: Can Renewable Energy Replace Fossil Fuels by 2050? Sustainability, 14, 4792.
  11. Idah, N., Ubeku, E., Eyenubo, O. , and Otuagoma, S. 2025. Design, Construction and Evaluation of 1.5 Kva, Fuel-Less Generator by Self Induction. International Journal of Advanced Multidisciplinary Research and Educational Development, 1, 381-397.
  12. Noor, F. , and Ullah, K. 2020. The Role of Energy in Facilitating Economic Development in Pakistan. Journal of Energy and Environmental Policy Options, 3, 104-111.
  13. Perera, F. , and Nadeau, K. 2022. Climate Change, Fossil-Fuel Pollution, and Children's Health. New England Journal of Medicine, 386, 2303-2314.
  14. Rahman, M. M., Oni, A. O., Gemechu, E. , and Kumar, A. 2020. Assessment of Energy Storage Technologies: A Review. Energy conversion and management, 223, 113295.
  15. Somoye, O. A. 2023. Energy Crisis and Renewable Energy Potentials in Nigeria: A Review. Renewable and Sustainable Energy Reviews, 188, 113794.
  16. Sunday, K. J. , and Taheri, M. L. 2017. Soft Magnetic Composites: Recent Advancements in the Technology. Metal Powder Report, 72, 425-429.
  17. Vagati, A., Fratta, A., Franceschini, G. , and Rosso, P. 2002. Ac Motors for High-Performance Drives: A Design-Based Comparison. IEEE Transactions on Industry Applications, 32, 1211-1219.
  18. Wang, J. , and Azam, W. 2023. Natural Resource Scarcity, Fossil Fuel Energy Consumption, and Total Greenhouse Gas Emissions in Top Emitting Countries. Geosci Front. 2024; 15 (2): 101757. J. GSF.
  19. Yang, Y., Xia, S., Huang, P. , and Qian, J. 2024. Energy Transition: Connotations, Mechanisms and Effects. Energy Strategy Reviews, 52, 101320.
How to Cite

Omoniyi, E. B., O, O. C., John-Taiwo, O, S., & T, A. S. (2025). Design and Performance Evaluation of a Battery-Assisted Fuel-Less Generator Using a Permanent Magnet Synchronous Generator with Automated Feedback Control. Nigerian Journal of Materials Science and Engineering, 15(1), 112-121.

E. B. Omoniyi, O. C. O, John-Taiwo, S. O, and A. S. T, "Design and Performance Evaluation of a Battery-Assisted Fuel-Less Generator Using a Permanent Magnet Synchronous Generator with Automated Feedback Control," Nigerian Journal of Materials Science and Engineering, vol. 15, no. 1, pp. 112-121, June 2025.

Share this article:
Facebook X / Twitter LinkedIn